G-SYSTEMS CONTROLLERS
GSE controller - EC temp, min and max speed (1 fan)
This EC fan controller has temperature, minimum- and maximum speed settings on three knobs for the exhaust fan. It is easy to use.
The EC fan controller is supplied with a 4m long cable including a 3.5mm 3pole stereo jack (Can-Fan) or RJ45 (Primaklima, Carbonactive) connector to the fan and a 4m long Temperature sensor. It comes as a finished product. The output signal is 0-10V or PWM (pulse width modulation) signal which can be set by a jumper.
An extremely low current consumption allows you to run the EC fan controller without power supply, powered directly from the EC fan.
Settings range:
Temperature: 20C° to 30C°
Minimum speed: off, 20% to -100%
Maximum speed: 100% to -50%
Is the power supply required?
With or without power supply? Depending your EC fan you need a supply current >10VDC >4mA and PWM signal you can run the controller without a own power supply. This information you have to get from the Technical data sheet of your EC fan. (Ruck or Can-Fan) EBM-papst motors, Primaklima, Systemair are working with PWM Signal)
If the EC-fan provide 2wire Signal-GND then yes,
Ii the EC-fan provide 3-4wire Signal-GND-VDC >10V/4mA there is no power supply required.
Packing contains:
1x EC fan controller incl. Sensor and fan supply cable
1x Power supply 12VDC 100mA (depending on the model)
Sizes and technical data:
Housing: Height = 90mm, Wide= 58mm, Depth= 40mm
Weight: 307g
Voltage: 12VDC
Power consumption: 4mA
Max. output limit <50mA per channel
Digital sensor 5V Measures temperatures from –55°C to +125°C (–67°F to +257°F)
0.5°C accuracy from –10°C to +85°C
Protection class: IP 20
Downloads
GSE Temperature & minimum speed control
The minimum speed controller is a temperature depended speed controller for ventilated rooms with one ore more fans. The minimum speed controller keeps the temperature constantly and impedes to run under the set minimum-speed. It can be easily controlled, adjusting the required temperature and the minimum speed on two knobs.
The variant with RJ45 connector is offering you 0-10V or PWM (pulse width modulation) signal for EC fans.
Two internal temperature sensors prevent overheating on heat-sink and processor parts. However should overheating occur, the variable control shuts off and a safety relay bypasses the extract air fan while the supply air fan is turned off. The controller thus prevents a total failure of the ventilation and protects your plants.
The controller comes as a finished part and is ready to use. This reliable fan controller comes complete with a sealed water resistant cover, plugs with flap-lids and a low voltage sensor making it perfect for humid rooms. The sensor comes with a 4meter long cable. The controller is supplied with a 1.5m power cord and a 4 meter sensor cable. This can be extended up to 10 meters if required.
Sizes and technical data's:
Case: WxHxD = 130x92x105mm
Controller: WxHxD = 160x130x105mm
Designed for: 10A / 2300W / TRIAC 1x16A
Volts: 230V / 50HZ
Digital sensor 5V Measures temperatures from –55°C to +125°C (–67°F to +257°F)
0.5°C accuracy from –10°C to +85°C
Protection class: IP54
Settings range:
Temperature: 20C° to -30C°
Minimum speed: off, 20% to -100%
Technical Data:
| Imax | 10A |
|---|---|
| VAmax | 2300W |
| Umax | 230V 50Hz |
| IP class | 54 |
GSE Water timer (230V Input or Light Sensor)
The Irrigation timer is used to control a pump to irrigate crops.
This timer is ideal for scheduled Ebb & Flow systems and normal irrigation droplets or NFT systems.
The pulse time and the interval time can be set separately for day and night irrigation. Depending on the model, the day/night switch on a photocell, or the power input is controlled.
Sizes and technical data's:
Size: WxHxD = 34x58x86 mm
Weight: 86 g
Volt: 230 V / 50 Hz
I max. = 2 A
Protection class: IP20
GSE controller - Controller for temperature and minimal speed 10A
The minimum speed controller keeps the temperature constant and prevents the speed from falling below a certain minimum. It can be easily controlled: the temperature and the minimum speed are adjusted by means of two buttons
Technical data and dimensions:
- Controller: WxHxD = 160x100x90mm
- Designed for: 10A / 2300W / TRIAC 1x16A
- 230V / 50Hz
- Digital sensor 5V Measures temperatures from -55 ° C to + 125 ° C (-67 ° F to + 257 ° F) 0.5 ° C accuracy from -10 ° C to + 85 ° C
- Protection class: IP54
The controllers greatly facilitate your work and the synchronization between the individual devices in your growing room. They provide complete control over the elements that make up your lighting and ventilation systems.
Humidity controller 10А
Humidity control could make the difference between a crop’s success and its failure.
This accurate plug and play controller for either a humidifier or dehumidifier makes controlling this environmental condition easy.
The unit comes complete in a waterproof casing, IP 44 rated, with a compatible mains socket with hinged lids, and a digital low voltage sensor, making it the perfect controller for humid rooms. Simply plug the unit in between the power supply and the humidifier or dehumidifier, set the desired humidity range, and let the controller take control.
The sensor is supplied with a 4-meter cable.
Settings range:
Humidity: 30% to 100%
Hysteresis:dehumidifier -10% to -1% and humidifier +1% to +10%
All G.S.E products are engineered and manufactured in Europe and are available exclusively from Growth Technology retailers.
